Skip to content

Cymbaluk Designs

CNC Router and Plasma Projects

  • Knowledge Base
    • FAQ
    • LinuxCNC Configuration
      • Basic Configuration
      • Plasma Configuration
      • 2.8 Master Branch & Gantry Homing
    • Wiring Information
  • CNC Builds
    • The First CNC Table
    • 6’x4′ Router Table
    • 2’x2′ Plasma Table
    • 4’x2′ Plasma Table
    • 4’x2′ Budget Plasma Table
    • 4’x4′ Plasma for My Shop
    • Lighter Duty 4×4

Lighter Duty 4×4

Coming Soon…..

Share this:

  • Twitter
  • Facebook

Like this:

Like Loading...

Enter your email address to follow and receive notifications of new posts by email.

Follow Me on Instagram

Out goes machine number 8. Got some room back in my garage. Time for a short break and some cleanup of all the tools. Linear rails and ball screws ordered to start on a HD 3'x2' milling table for aluminum. #cnc #cncplasma #metalfab #metalfabrication #welding #linuxcnc #plasmacutting #hypertherm #cncplasmacutting #hobartwelders #homemadetools #welds #weld #metalart
Ohmic sensing on some 16ga. Found the 45xp to be a little temperamental with its divided voltage reading output if the torch is too close to the material, few small changes to some settings to keep the torch out of that zone and it's good to go. #cnc #cncplasma #metalfab #metalfabrication #welding #linuxcnc #plasmacutting #hypertherm #cncplasmacutting #hobartwelders #homemadetools #welds #weld #metalart
Tons of test cuts today on the 5x5. Had a training session with the new owner and everything looking good. Project is done and should be out of here within the next few weeks. My router table, second machine I ever built, has done me well over the years but it was time to retire it. Was looking at a few different ways to retrofit it but decided to just build from scratch, not sure what size I want or timeframe for that build but it will be in the works. #cnc #cncplasma #cncrouter #metalfab #metalfabrication #welding #linuxcnc #plasmacutting #hypertherm #cncplasmacutting #hobartwelders #homemadetools #welds #weld #metalart
Dialed in real good on 16ga with the finecuts. T is a mock up of a folding 3in cube to test squareness. Picture is of the backside right off the machine with no touch up, dross is almost nonexistent. #cnc #cncplasma #metalfab #metalfabrication #welding #linuxcnc #plasmacutting #hypertherm #cncplasmacutting #hobartwelders #homemadetools #welds #weld #metalart #powermax45xp
Success! Few software tweaks to do and this table is a wrap. New owner will be here soon for a day or two of training and I'll have some garage space back. #cnc #cncplasma #metalfab #metalfabrication #welding #linuxcnc #plasmacutting #hypertherm #cncplasmacutting #hobartwelders #homemadetools #welds #weld #metalart #45xp
Wiring is done, all signals tested and we have motion/homing sequence success. Need to slap the torch on, make a few config tweaks and wait for a longer monitor cable to show up. Should be test cutting next weekend. #cnc #cncplasma #metalfab #metalfabrication #welding #linuxcnc #plasmacutting #hypertherm #cncplasmacutting #hobartwelders #homemadetools #welds #weld #metalart
Create a website or blog at WordPress.com
  • Knowledge Base
    • FAQ
    • LinuxCNC Configuration
      • Basic Configuration
      • Plasma Configuration
      • 2.8 Master Branch & Gantry Homing
    • Wiring Information
  • CNC Builds
    • The First CNC Table
    • 6’x4′ Router Table
    • 2’x2′ Plasma Table
    • 4’x2′ Plasma Table
    • 4’x2′ Budget Plasma Table
    • 4’x4′ Plasma for My Shop
    • Lighter Duty 4×4
%d bloggers like this: